01 ยท Small jobs
Ceramic Series
$201$435Save $234
In the box
- Ceramic nozzle
- Suction feed line
- 2 spare ceramic nozzles
Pick your system by job size
Every SBK system runs on the pressure washer you already own. Start small or go straight to the Tank Rig.
Three ways in. All run on your pressure washer.
Each setup is matched to a job size. The bigger rigs come loaded with free gifts.
02 ยท Mid-size jobs
The Bag Rig
$652$1,034Save $382
In the box
- Carbide 600 nozzle
- Blasting wand + 12 ft feed hose
- Gravity-fed bag system (150 lb PVC)
- Patent-pending metering sleeve valve + air assist)
Free this Black Friday
-
Media Sifter+ Recovery TarpFree $73 -
Blasting apronFree $51 -
Blasting suit, face mask, glovesFree $37
03 ยท Big jobs
The Tank Rig
$1,304$1,862Save $558
In the box
- Carbide 600 nozzle
- Blasting wand + 12 ft feed hose
- Patent-pending metering sleeve valve + air assist)
- Inductor tank + stand (up to 250 lb per fill)
Free this Black Friday
-
Carbide 600 nozzleFree $117 -
Sand sifter + Recovery tarpFree
$73 -
Blasting apronFree
$51 -
Face MaskFree
$37
Ceramic or Carbide 600 nozzles can still be bought alone in the Shop.
See each rig on a real job.
Up closeRust off in one pass
Rear frameChevy Caprice ยท Tank Rig
Raptor hoodPaint to bare metal ยท timelapse
The Tank Rig
$1,304$1,862
Big jobs eat media. The 250 lb tank keeps you blasting.
The Bag Rig
$652$1,034
Carbide nozzle + gravity bag. No clogs, best value.
Ceramic Series
$201$435
Tight, controlled stream for parts. Runs on any washer.
Ceramic Series
$201$435
Gets the most out of a smaller washer.
Your answers
Three setups. Pick your job size.
All three run on the pressure washer you already have.
 |  | Best for big jobs | |
|---|---|---|---|
| Best for | Panels, parts, wheels | Frames, trailers, mid-size jobs | Full shells, big jobs |
| Nozzle | Ceramic | Carbide 600 | Carbide 600 |
| Media feed | Suction line | Gravity-fed bag | Inductor tank + stand |
| Media per fill | One bucket | One bag | Up to 250 lb |
| Clog-resistant feed | |||
| Free ceramic kit + suction feed | |||
| Free media sifter | |||
| Free suit, face mask, gloves | |||
| Free catch net | |||
| Free Rust Inhibitor + AP1 | |||
| Shop now | Shop now | Shop now | Shop now |
Load 250 lb. Blast until the job's done.
The inductor tank feeds media steadily straight into the Carbide 600 nozzle. No sputtering, no clogs, no shaking a bucket every five minutes.
- Up to 250 lb of media per fill
- Steady gravity feed: no clogs, no sputtering
- Carbide 600 nozzle built for full shells
Or build your own setup
Nozzle first, then how you feed the media.
Pick the nozzle by job size.
-
SalePressure Washer Sandblasting Kit
$201.00
$435.00 -
SaleCarbide 600
$432.00
$723.00
Bag or tank: no clogs, no shaking a bucket.
-
SaleGravity-Fed Delivery System
$291.00
$416.00 -
SaleGravity-Fed Delivery System + Stand
$580.00
$830.00 -
SaleGravity-Fed System โ Inductor Tank
$580.00
$829.00 -
SaleGravity-Fed System โ Inductor Tank + Stand
$868.00
$1,249.00 -
SaleGravity-Fed System Stand
$348.00
$493.00
Nozzle + delivery in one box. Free gifts included.
-
Sale
Carbide 600 Pro โ Inductor Tank System
$1,304.00
$1,862.00 -
SaleCarbide 600 Pro โ Gravity-Fed Bag System
$652.00
$1,034.00 -
SaleCeramic Pro โ Gravity-Fed Bag System
$463.00
$698.00 -
SaleCarbide 600 Pro Blasting Bundle
$1,016.00
$1,452.00
Asked on every call. Answered here.
Straight answers to what everyone wants to know before their first blast.
Question 01
Which pressure washer do I need?
The one you already have, gas or electric. Flow (GPM) matters as much as pressure: a washer with good flow often blasts better than a higher-PSI one with weak flow.
- Sweet spot: 2,500โ3,000 PSI for regular blasting, 3,000+ PSI with good GPM for heavy rust.
- Ceramic Series: built for washers up to about 5,000 PSI.
- Carbide 600: tungsten carbide nozzle rated to 600 bar, for the biggest machines and longest jobs.
Question 02
Which media should I use?
Dry, coarse media only.
- Black Diamonds: aggressive and fast. Heavy rust, thick paint, frames, trailers.
- Crushed Glass: more control and a smoother finish. Lighter rust and panels.
Never use play sand. It's too fine, holds moisture and is the fastest way to clog the line.
Question 03
How long does the nozzle last?
Ceramic nozzles are wear parts. How long they last depends on your media and pressure, which is why the Ceramic Series ships with 2 spares. The Carbide 600 nozzle is solid tungsten carbide and lasts many times longer, so it's the one for full shells, frames and repeat jobs.
Signs it's time for a new nozzle: the pattern gets wider, cutting slows down and you burn through more media.
Question 04
What aftercare do I need? (Rust inhibitor)
Bare metal flash-rusts within hours once it's wet. Two steps stop it:
- Add Rust Inhibitor to your blast water at 1 oz per gallon, so the surface stays clean while you work.
- Once it's dry, apply AP1 Conversion Coating to lock the metal down before primer.
Question 05
How do I avoid clogs?
- Starting: water on first, then open the media.
- Stopping: media off first, then water off.
- Use dry, sifted media. Damp clumps and pebbles cause almost every clog.
The gravity-fed bag and tank systems feed media steadily, so they don't clog the way a suction bucket can.
01Which pressure washer do I need?
The one you already have, gas or electric. Flow (GPM) matters as much as pressure: a washer with good flow often blasts better than a higher-PSI one with weak flow.
- Sweet spot: 2,500โ3,000 PSI for regular blasting, 3,000+ PSI with good GPM for heavy rust.
- Ceramic Series: built for washers up to about 5,000 PSI.
- Carbide 600: tungsten carbide nozzle rated to 600 bar, for the biggest machines and longest jobs.
02Which media should I use?
Dry, coarse media only.
- Black Diamonds: aggressive and fast. Heavy rust, thick paint, frames, trailers.
- Crushed Glass: more control and a smoother finish. Lighter rust and panels.
Never use play sand. It's too fine, holds moisture and is the fastest way to clog the line.
03How long does the nozzle last?
Ceramic nozzles are wear parts. How long they last depends on your media and pressure, which is why the Ceramic Series ships with 2 spares. The Carbide 600 nozzle is solid tungsten carbide and lasts many times longer, so it's the one for full shells, frames and repeat jobs.
Signs it's time for a new nozzle: the pattern gets wider, cutting slows down and you burn through more media.
04What aftercare do I need? (Rust inhibitor)
Bare metal flash-rusts within hours once it's wet. Two steps stop it:
- Add Rust Inhibitor to your blast water at 1 oz per gallon, so the surface stays clean while you work.
- Once it's dry, apply AP1 Conversion Coating to lock the metal down before primer.
05How do I avoid clogs?
- Starting: water on first, then open the media.
- Stopping: media off first, then water off.
- Use dry, sifted media. Damp clumps and pebbles cause almost every clog.
The gravity-fed bag and tank systems feed media steadily, so they don't clog the way a suction bucket can.
Not sure which setup? Call us.
Tell us your pressure washer and your project. We'll tell you exactly which setup and media to get, and what you don't need.